Cart (0)
  • No items in cart.
Total
$0
There is a technical issue about last added item. You can click "Report to us" button to let us know and we resolve the issue and return back to you or you can continue without last item via click to continue button.
Filters:
FORMAT
EDITION
to
PUBLISHER
(1)
(337)
(589)
(55)
(234)
(996)
(690)
(2161)
(117)
(94624)
(54)
(575)
(124)
(33)
(21)
(20)
(94991)
(3)
(17)
(1)
(374)
(315)
(6731)
(241)
(16)
(6)
(1646)
(17)
(19)
(28)
(4)
 
(6)
(7)
(115)
(3)
(57)
(5)
(5)
(1)
(1)
(2)
(25)
(27)
(27)
(13)
(61)
(24)
(22)
(7)
(8)
(20)
(1)
(3)
(50)
(6)
(33)
CONTENT TYPE
 Act
 Admin Code
 Announcements
 Bill
 Book
 CADD File
 CAN
 CEU
 Charter
 Checklist
 City Code
 Code
 Commentary
 Comprehensive Plan
 Conference Paper
 County Code
 Course
 DHS Documents
 Document
 Errata
 Executive Regulation
 Federal Guideline
 Firm Content
 Guideline
 Handbook
 Interpretation
 Journal
 Land Use and Development
 Law
 Legislative Rule
 Local Amendment
 Local Code
 Local Document
 Local Regulation
 Local Standards
 Manual
 Model Code
 Model Standard
 Notice
 Ordinance
 Other
 Paperback
 PASS
 Periodicals
 PIN
 Plan
 Policy
 Product
 Product - Data Sheet
 Program
 Provisions
 Requirements
 Revisions
 Rules & Regulations
 Standards
 State Amendment
 State Code
 State Manual
 State Plan
 State Standards
 Statute
 Study Guide
 Supplement
 Sustainability
 Technical Bulletin
 All
  • BSI
    PAS 1188-4:2014 Flood protection products. Specification - Demountable products
    Edition: 2014
    $227.73
    / user per year

Description of PAS 1188-4:2014 2014

This PAS specifies requirements for the designation, testing, factory production control, installation documentation and marking for different types and configurations of flood protection products intended to be demountable, for use away from buildings, but may be sealed against structures or buildings at section ends, in the UK or locations with similar exposures, i.e. where there is a temperate climate.

This PAS specifies the method of testing and an allowable leakage rate.

NOTE 1 The PAS test conditions (see Annex B) represent typical conditions that can be experienced during a flood. This includes testing the product on a concrete base for leakage and structural failure under static water levels, random waves up to 0.1 m high and parallel currents up to 1.0 m/s.

NOTE 2 This PAS does not cover testing with contaminated or saline water; however, product manufacturers are required to provide information about the performance of their products in these conditions (see Annex C).

NOTE 3 Flood protection products that conform to this PAS might not be suitable for all locations, exposures and foundation types. Further guidance is set out in Delivering benefits through evidence: Temporary and demountable flood protection guide [2], Six steps to property level flood resilience: Guidance for property owners [9] and guidance can also be obtained from the Flood Protection Association or from the National Flood Forum or Scottish Flood Forum or other qualified professional advisers.

NOTE 4 Extreme loading conditions such as those resulting from turbulent water or static water head (above designated maximum water depth) or debris impact are not covered by testing in this PAS. In these locations the product and system are specifically designed and/or tested to withstand such stresses.

NOTE 5 Demountable flood protection products are normally installed in conjunction with a pumping arrangement to remove any excessive leakage.

NOTE 6 The installation of flood protection products described in this PAS are not intended to provide permanent flood protection. These flood protection products are installed or activated in the event of an imminent flood and removed or deactivated as soon as danger from flooding is over.

This PAS is not applicable to flood protection products for installation across building apertures such as individual doors, windows, air-bricks and air vents or around buildings; these are covered by PAS 1188‑1 and PAS 1188‑3.

This PAS is not applicable to temporary flood protection products which are not location specific in their use, are intended to be wholly installed during a flood event and wholly removed afterwards; these are covered by PAS 1188‑2.



About BSI

BSI Group, also known as the British Standards Institution is the national standards body of the United Kingdom. BSI produces technical standards on a wide range of products and services and also supplies certification and standards-related services to businesses.

GROUPS