FORMAT
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-G83 1996ASTM G83-96Withdrawn Standard: Standard Test Method for Wear Testing with a Crossed-Cylinder Apparatus (Withdrawn 2005)ASTM G83Scope 1.1 This test method describes a laboratory test for determining the resistance of metallic materials to metal-to-metal wear produced in a crossed cylinder apparatus. The intent of this test method is to produce data that will reproducibly rank materials in their resistance to wear and evaluate the compatibility of different metal couples. The test method is normally used to determine the wear resistance of a material when it wears against itself. However, the test can also be used to evaluate the compatibility of different materials. 1.2 When the rotating and stationary bars are of the same material, wear test results are reported as the total volume loss in cubic millimetres for the rotating and stationary cylinders. The manner of recording the results also specifies the particular test procedure used. The value is obtained by adding the volume loss of the rotating member to the volume loss of the nonrotating member. Materials of higher wear resistance will have lower volume loss. Note 1-To attain uniformity among laboratories, it is the intent of this test method to require that volume loss due to wear be reported only in the metric system as cubic millimetres (1 mm = 6.102 X 10 in. ).1.3 When dissimilar materials are being tested, wear test results are reported as the volume loss in cubic millimetres for the rotating and stationary test bars separately. When two different metals or alloys are tested, it is also recommended that each metal or alloy be tested in both the stationary and moving positions. Then, for each metal or alloy, the combined volume of wear in both positions should be used in comparisons with self-mated wear volume. 1.4 The test method describes three recommended procedures that are appropriate for different degrees of wear resistance. Note 2-The crossed cylinder wear test inherently exhibits a time varying contact area. A plot of wear volume versus sliding distance is typically nonlinear. Therefore, results obtained using parameters other than those specified in the test method cannot be used to calculate an expected value.1.4.1 Procedure A -This is a relatively severe test that will rank metallic materials which have high-wear resistance. Materials with wear resistance in the high-speed tool steel category are particularly suited to this test. 1.4.2 Procedure B -This is a short-term variation of Procedure A. 1.4.3 Procedure C -This is a lower speed and shorter term variation of Procedure A that is particularly useful in ranking materials of low-wear resistance. 1.5 In reporting, the values stated in SI units are preferred. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Keywords Compatibility; Crossed-cylinder apparatus; Falex method; Metals and metallic materials; Metal-to-metal contact; Nonrotating cylinder; Resistance-water; Rotating bars/cylinders; Stationary bars; Volume change; Wear testing-metallic materials; wear testing (of metallic materials) with a cross-cylinder apparatus ICS Code ICS Number Code 17.040.20 (Properties of surfaces) DOI: 10.1520/G0083-96 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|