|
FORMAT
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-F3664 2024ASTM F3664-24Active Standard: Standard Practice for Blast TestingASTM F3664Scope 1.1 Purpose—The primary purpose of this practice is to define good commercial and customary practice for conducting blast tests of physical security products, related devices, and systems. The goal is to harmonize results between test facilities and maximize the consistency and repeatability of the results obtained from these blast tests. This practice shall be used for blast simulator testing, where applicable. 1.2 Objectives—Objectives guiding the development of this practice are: 1.2.1 Formalize standard practices for conducting blast tests. 1.2.2 Facilitate high-quality, standardized results processing and reporting of test results. 1.2.3 Use as a starting point for a best practice standard that will grow into an industry standard both domestically and internationally. 1.2.4 It is anticipated that this practice will evolve over time as requirements and facility capabilities change. 1.2.5 This practice should not be considered the limit of requirements for proper completion of a given test program. There may be additional requirements depending on the application and the threat. 1.3 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.4 Omissions—The omission of any specific explosive, instrumentation type, material type, or test configuration does not necessarily preclude its use in accordance with this practice, as long as all applicable provisions are satisfied. 1.5 The following is a table of contents for this practice: 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords airblast; blast; explosive; impulse; instrumentation; mitigation; peak pressure; pressure; test plan; ICS Code ICS Number Code 71.100.30 (Explosives. Pyrotechnics and fireworks) DOI: 10.1520/F3664-24 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|