|
FORMAT
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-F3612 2024ASTM F3612-24Active Standard: Standard Practice for Lower Extremity Exoskeleton Locomotion TransitionsASTM F3612Scope 1.1 When an exoskeleton operator moves within their environment, they will encounter transitions (for example, level ground to ramps or stairs). These environments and transitions will naturally require different biomechanical patterns (1).2 As such, it is important to evaluate an exoskeleton’s ability to perform transitions during human-exoskeleton operation. 1.2 This practice provides tools for assessing an exoskeleton’s ability to transition between objects or structures in the environment. Apparatus and desired performance criteria are identified to support transition assessment and direct and perceived measures of performance are provided. 1.3 Purpose: 1.3.1 This practice provides a set of instructions for the evaluation of an exoskeleton’s (see Terminology F3323) ability to transition (see definitions in Section 3) between representative apparatus in the environment. 1.3.2 This practice can be used independently or can be applied for use with test methods (for example, gait transitioning to ramps). A test report is therefore included and provides an independent evaluation of transition. 1.3.3 This practice contributes to the evaluation of exoskeletons within the domains of industry, military, medical, emergency response, and recreation. Exoskeletons possess a certain set of allowable user movements that may vary by task and goals. Environments in these typical sectors often pose constraints to exoskeleton user movement to various degrees. Being able to transition as intended by the user or test requestor while using an exoskeleton is essential for exoskeleton deployment in a use-case relevant environment. 1.3.4 This practice provides four suggested course configurations that recreate transition scenarios based on anticipated environments, apparatus, and applicable transitions. This practice includes metrics and build criteria for these courses. Alternate course configurations may be selected and should be documented following the guidelines provided. 1.4 Exoskeletons should be able to smoothly transition between different apparatus without undesired or detrimental reactions. Intended exoskeleton purpose by the manufacturer will determine the relevant apparatus configurations and test methods to be used. 1.5 Performing Location—This practice should be performed in a testing laboratory or the field where the specified apparatus and environmental conditions are implemented. 1.6 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords obstacles; performance metrics; ramps; stairs; user preference; ICS Code ICS Number Code 11.180.10 (Aids and adaptation for moving) DOI: 10.1520/F3612-24 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|