FORMAT
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-F2412 2011ASTM F2412 - 11Standard Test Methods for Foot ProtectionActive Standard ASTM F2412 | Developed by Subcommittee: F13.30 Book of Standards Volume: 15.07 ASTM F2412Significance and Use These test methods contain requirements to evaluate the performance of footwear for the following: Impact resistance for the toe area of footwear (I/75), Compression resistance for the toe area of footwear (C/75), Metatarsal protection that reduces the chance of injury to the metatarsal bones at the top of the foot (Mt/75), Conductive properties which reduce hazards that may result from static electricity buildup, and reduce the possibility of ignition of explosives and volatile chemicals (Cd), Electric Hazard by stepping on live wire (EH), Static dissipative (SD) properties to reduce hazards due to excessively low footwear electrical resistance that may exist where SD footwear is required, and Puncture resistance footwear devices (PR). Any changes to the original components of safety toe footwear such as replacing or adding after market footbeds/inserts could cause non compliance to any or all parts of this standard rendering the ASTM label invalid. Protective toe footwear specimens or samples shall be retested for any of the following changes. Change in material used to make protective toe cap, change in protective cap manufacturer, change in the design of the toe cap. Change in construction method used to make footwear or change in factory in which footwear is produced. Change in the upper or insole material thickness greater than 25 %, change to the soling system or a change in the hardness of the outsole. Change in shape of last used in the manufacturing of footwear. Change in material or supplier of protective insole. Change in material or supplier of met guard. 1. Scope 1.1 These test methods measure the resistance of footwear to a variety of hazards that can potentially result in injury. 1.2 These test methods may be used to test for compliance to minimum performance requirements in established safety standards. 1.2.1 By agreement between the purchaser and the supplier, or as required by established safety standards, these test methods can be used to determine any one, or all of the following: (1) impact resistance (I), (2) compression resistance (C), (3) metatarsal impact resistance (Mt), (4) resistance to electrical conductivity (Cd), (5) resistance to electric hazard (EH), (6) static dissipative performance (SD), and (7) puncture resistance (PR). 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards B117 Practice for Operating Salt Spray (Fog) Apparatus CSA Standard CAN/CSAZ195 Protective FootwearKeywords chain saw protection; conductive footwear; dielectric; electric shock resistance (EH); foot protection; impact resistance; metatarsal protection; protective footwear; puncture resistance; safety footwear electrical hazard; static dissipative (ESD; ICS Code ICS Number Code 13.340.50 (Leg and foot protection) DOI: 10.1520/F2412-11 ASTM International is a member of CrossRef. ASTM F2412The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|