Cart (0)
  • No items in cart.
Total
$0
There is a technical issue about last added item. You can click "Report to us" button to let us know and we resolve the issue and return back to you or you can continue without last item via click to continue button.
Home
Content
eLibrary
Filters:
FORMAT
EDITION
to
PUBLISHER
AABC
(1)
AAMI
(338)
ACI
(589)
AECDAILY
(599)
AISC
(55)
ASA
(234)
ASCE
(1006)
ASHRAE
(696)
ASME
(2183)
ASSE
(117)
ASTM
(95207)
AWC
(63)
AWWA
(575)
BHMA
(124)
BICSI
(33)
BIFMA
(21)
BOMA
(20)
BSI
(95735)
CHD
(3)
CRSI
(17)
IAHSS
(1)
IAPMO
(374)
ICC
(324)
IEEE
(6938)
IES
(241)
ISEA
(21)
Joint Commission
(184)
Joint Commission Int.
(1)
NETA
(6)
NFPA
(1667)
TCNA
(18)
TMS
(19)
USGBC
(28)
WILEY
(4)
 
AR
(6)
AZ
(7)
CA
(115)
CT
(3)
FL
(57)
ID
(5)
IL
(5)
IN
(1)
KY
(1)
LA
(2)
MI
(25)
MN
(27)
NC
(27)
NJ
(13)
NY
(61)
OH
(24)
OR
(22)
PA
(7)
RI
(8)
SC
(20)
SD
(1)
TX
(3)
VA
(50)
VT
(6)
WA
(33)
CONTENT TYPE
 Act
 Admin Code
 Announcements
 Bill
 Book
 CADD File
 CAN
 CEU
 Charter
 Checklist
 City Code
 Code
 Commentary
 Comprehensive Plan
 Conference Paper
 County Code
 Course
 DHS Documents
 Document
 Errata
 Executive Regulation
 Federal Guideline
 Firm Content
 Guideline
 Handbook
 Interpretation
 Journal
 Land Use and Development
 Law
 Legislative Rule
 Local Amendment
 Local Code
 Local Document
 Local Regulation
 Local Standards
 Manual
 Model Code
 Model Standard
 Notice
 Ordinance
 Other
 Paperback
 PASS
 Periodicals
 PIN
 Plan
 Policy
 Product
 Product - Data Sheet
 Program
 Provisions
 Requirements
 Revisions
 Rules & Regulations
 Standards
 State Amendment
 State Code
 State Manual
 State Plan
 State Standards
 Statute
 Study Guide
 Supplement
 Sustainability
 Technical Bulletin
 All
  • ASTM
    F1438-93(2020) Standard Test Method for Determination of Surface Roughness by Scanning Tunneling Microscopy for Gas Distribution System Components
    Edition: 2020
    $103.58
    Unlimited Users per year

Description of ASTM-F1438 2020

ASTM F1438-93-Reapproved2020

Withdrawn Standard: Standard Test Method for Determination of Surface Roughness by Scanning Tunneling Microscopy for Gas Distribution System Components (Withdrawn 2023)




ASTM F1438

Scope

1.1 The purpose of this test method is to define a method for analyzing the surface texture of the above-mentioned components using a scanning tunneling microscope (STM). STM is a noncontact method of surface profiling that can measure three-dimensional surface features in the nanometer size range, which can then be used to represent the surface texture or to provide figures of merit. Application of this test method, where surface texture is used as a selection criterion, is expected to yield comparable data among different components tested.

1.2 Limitations: 

1.2.1 This test method is limited to characterization of stainless steel surfaces that are smoother than Ra = 0.25 μm, as determined by a contact-stylus profilometer and defined by ANSI B46.1. The magnifications and height scales used in this test method were chosen with this smoothness in mind.

1.2.2 Intentional etching or conductive coating of the surface are considered modifications of the gas-wetted surface and are not covered by this test method.

1.2.3 This test method does not cover steels that have an oxide layer too thick to permit tunneling under the test conditions outlined in 11.3.

1.3 This technique is written with the assumption that the STM operator understands the use of the instrument, its governing principles, and any artifacts that can arise. Discussion of these points is beyond the scope of this test method.

1.4 The values stated in SI units are to be regarded as the standard.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


Keywords

average roughness; clean room; components; microscope; profile; roughness; scanning; stainless steel; surface; texture; topography; tunneling;


ICS Code

ICS Number Code 17.040.20 (Properties of surfaces)


DOI: 10.1520/F1438-93R20

GROUPS