|
FORMAT
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-E3419 2024ASTM E3419-24Active Standard: Standard Digital Reference Images for Steel Fusion WeldsASTM E3419Scope 1.1 This standard provides digital reference images for steel fusion welds that contain typical discontinuities with varying severity levels in different thicknesses of material. The digital reference images are an adjunct to this standard and must be purchased separately from ASTM International if needed. 1.2 There are three volumes of digital reference images based on seven nominal weld thicknesses as follows: 1.2.1 Vol I—Set of 23 images covering base material up to and including 1/4 in. (6.4 mm) in thickness. 1.2.2 Vol II—Set of 30 images covering base material over 1/4 up to and including 3 in. (6.4 to 76 mm) in thickness. 1.2.3 Vol III—Set of 7 images covering base material over 3 up to and including 8 in. (76 to 203 mm) in thickness. 1.3 Units—The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 All areas of this standard may be open to agreement between the cognizant engineering organization and the supplier, or specific direction from the cognizant engineering organization. These items should be addressed in the purchase order or the contract. 1.5 Only licensed copies of the software and images shall be utilized for production inspection. A copy of the ASTM/user license agreement shall be kept on file for audit purposes. (See Note 1.) Note 1: The set of digital reference images consists of sixty digital data files, and software to load the desired format and specific instructions on the loading process. The sixty reference images illustrate both graded discontinuities and ungraded discontinuities. Available from ASTM International Headquarters, order Nos: RRE341901, RRE341902, and RRE341903. 1.6 These digital reference images are not intended to illustrate the types and degrees of discontinuities found in steel fusion welds when performing film radiography. If performing film radiography of such weldments, refer to Reference Radiographs E390. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords discontinuities; fusion welds; gamma ray; reference radiographs; steel; X-ray; ICS Code ICS Number Code 25.160.40 (Welded joints and welds) DOI: 10.1520/E3419-24 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|