|
FORMAT
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-E3112/E3112M 2020ASTM E3112/E3112M-20Active Standard: Standard Test Method for Ballistic-resistant Products and Shoot PacksASTM E3112/E3112MScope 1.1 This test method assesses resistance to complete penetration by projectiles and applies to ballistic-resistant products or shoot packs, either flexible or rigid, that are intended to provide protection against projectiles from small arms.2 This test method does not assess blunt impact resistance. 1.2 This test method does not apply to body armor, armor panels, inserts, trauma packs, trauma plates, materials, or other items intended to be worn or located against the body to limit blunt trauma. 1.3 This test method applies only to products related to homeland security and public safety. 1.4 This test method is not intended to address architectural products covered by Test Method F1233, such as building materials and security glazing. 1.5 This test method is applicable to products or shoot packs that are constructed with identical layups of ballistic materials over the entire product or shoot pack. The product or shoot pack may have stitching, seams, or other joints. Note 1: For example, this test method is applicable for evaluating a ballistic-resistant blanket constructed from multiple sheets of different materials laminated together; however, this test method is not applicable for evaluating a ballistic-resistant shield that has a discontinuity at the interface between opaque and transparent component materials. 1.6 The test method does not specify performance criteria or usage of the test results. 1.7 It is anticipated that this test method will be referenced by certifiers, purchasers, or other users in order to meet their specific needs. 1.7.1 In this test method, “other standards and specifications” and “unless specified elsewhere” refer to documents (for example, military standards, purchase specifications) that require the use of this test method. Purchasers and other users are responsible for the “other standards and specifications” and for specifying any requirements that supersede those of this test method. 1.7.2 Purchasers and other users will specify the ballistic test threats, and the associated velocities, to be used. 1.8 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.8.1 The user of this standard will identify the system of units to be used, and it is critical to ensure that any cross-referenced standards maintain consistency of units between standards. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords ballistic protection; ballistic resistance; ballistic-resistant products; ICS Code ICS Number Code 95.020 (Military in general) DOI: 10.1520/E3112_E3112M-20 The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|