|
FORMAT
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-E3109 2024ASTM E3109-18-Reapproved2024Active Standard: Standard Specification for Protective Gloves Worn by Law Enforcement and Corrections OfficersASTM E3109Scope 1.1 This specification addresses protective gloves worn by law enforcement and corrections officers. 1.2 This specification and related standards were developed by subject matter experts, including experienced end users, using data from a survey of more than 800 U.S. law enforcement and corrections officers. 1.3 This specification addresses performance requirements, performance ratings, and test methods for whole gloves and for glove components (for example, materials, layers). Note 1: This specification references published ASTM standards. 1.3.1 A glove is not uniform in terms of the protection it provides, and different portions or areas of a glove (for example, palm, fingertip) may offer different protection. 1.3.2 It is not intended that a single glove meet all specified performance requirements within this specification. 1.4 The glove supplier will identify which of the performance requirements a specific glove meets and the performance ratings for the different portions or areas of the glove. 1.5 This specification specifies performance requirements for (1) physical protection, including resistance to cut, puncture, and needle stick, and (2) resistance to abrasion and tearing to ensure protection is maintained during use. 1.5.1 A document outlining dexterity and other physical protection requirements identified by end users as important is being developed. 1.6 It is expected that this specification will be used by suppliers, test laboratories, certification bodies, and purchasers. 1.7 It is intended that two related standards be used in conjunction with this specification: 1.7.1 Guide E3212; and 1.7.2 Practice E3108. 1.8 Units—The values stated in SI or CGS2 units are to be regarded as standard. The primary units displayed in this standard are consistent with the referenced ASTM test methods. The values given in parentheses are mathematical conversions that are provided for information only. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords corrections; gloves; law enforcement; personal protective equipment; ICS Code ICS Number Code 13.340.40 (Hand and arm protection) DOI: 10.1520/E3109-18R24 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|