ASTM-E2375, 2013 - MADCAD.com

ASTM E2375 - 08(2013)

Standard Practice for Ultrasonic Testing of Wrought Products

Active Standard ASTM E2375 | Developed by Subcommittee: E07.06

Book of Standards Volume: 03.03

ASTM E2375

Significance and Use

4.1 This practice is intended primarily for the examination of wrought metals, forged, rolled, machined parts or components to an ultrasonic class most typically specified in the purchase order or other contract document.

1. Scope

1.1 Purpose This practice establishes the minimum requirements for ultrasonic examination of wrought products.

Note 1 This standard was adopted to replace MIL-STD-2154, 30 Sept. 1982. This standard is intended to be used for the same applications as the document which it replaced. Users should carefully review its requirements when considering its use for new, or different applications, or both.

1.2 Application This practice is applicable for examination of materials such as, wrought metals and wrought metal products.

1.2.1 Wrought Aluminum Alloy Products Examination shall be in accordance with Practice B594 .

1.3 Acceptance Class When examination is performed in accordance with this practice, engineering drawings, specifications, or other applicable documents shall indicate the acceptance criteria. Five ultrasonic acceptance classes are defined in Table 1 . One or more of these classes may be used to establish the acceptance criteria or additional or alternate criteria may be specified.

^A Any discontinuity with a response greater than the response from a flat-bottom hole or equivalent notch (see footnote ^B ) at the estimated discontinuity depth and the discontinuity size given is not acceptable.

^B See Fig. 3 , Fig. 4 , or Fig. 5 for dimensions of notches and holes when these are required for angle beam examination of tube walls and near-surface regions of cylindrical parts and other products.

^C Multiple discontinuities with indications greater than the response from a reference flat-bottom hole or equivalent notch at the estimated discontinuity depth of the size given (diameter) are not acceptable if the centers of any two of these discontinuities are less than one inch apart (not applicable to Class C).

^D Any discontinuity longer than the length given with indications equal to or greater than the response given (flat-bottom hole or notch response) is not acceptable. Not applicable to Class C).

^E Loss of back reflection by more than 50?%, when compared to non-defective material in the same or a similar part, is not acceptable.

^F For longitudinal examination of material over 6-in. (152.4-mm) thick in the short transverse direction, any loss of back reflection equal to or greater than 12 dB over an area 2 by 2 in. (50.8 by 50.8 mm) is rejectable. (Noise level is not relevant to this back reflection evaluation.

^G Noise which exceeds the alarm level setting (see 7.4.10.7 ), is not acceptable, except for titanium. For titanium alloys, the alarm level may be set just above the noise level, but shall not exceed 70?% of the reference standard response.

^H When examining titanium, Class AA and Class AAA, no rejection shall be made on the basis of noise level, if within the limits specified in footnote ^G .

^I Evaluation may be done by setting up on a ³ / ₆₄ in. (1.19 mm) hole and adding 7 dB of gain. (Also see Note 5 under Table 5 .)

1.4 Order of Precedence Contractual requirements and authorized direction from the cognizant engineering organization may add to or modify the requirements of this practice. Otherwise, in the event of conflict between the text of this practice and the references cited herein, the text of this practice takes precedence. Nothing in this practice, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.

1.5 Measurement Values The values stated in inch-pounds are to be regarded as standard. The metric equivalents are in parentheses.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

B107/B107M Specification for Magnesium-Alloy Extruded Bars, Rods, Profiles, Tubes, and Wire

B221 Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes

B241/B241M Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube

B594 Practice for Ultrasonic Inspection of Aluminum-Alloy Wrought Products for Aerospace Applications

E127 Practice for Fabricating and Checking Aluminum Alloy Ultrasonic Standard Reference Blocks

E164 Practice for Contact Ultrasonic Testing of Weldments

E213 Practice for Ultrasonic Testing of Metal Pipe and Tubing

E317 Practice for Evaluating Performance Characteristics of Ultrasonic Pulse-Echo Testing Instruments and Systems without the Use of Electronic Measurement Instruments

E428 Practice for Fabrication and Control of Metal, Other than Aluminum, Reference Blocks Used in Ultrasonic Testing

E543 Specification for Agencies Performing Nondestructive Testing

E1065 Guide for Evaluating Characteristics of Ultrasonic Search Units

E1158 Guide for Material Selection and Fabrication of Reference Blocks for the Pulsed Longitudinal Wave Ultrasonic Testing of Metal and Metal Alloy Production Material

E1316 Terminology for Nondestructive Examinations

American Society for Nondestructive Testing (ASNT) Standards

ANSI/ASNT-CP-189 ASNT Standard for Qualification and Certification of Nondestructive Testing Personnel

Society for Automotive Engineers (SAE) Standards

AMS6484 Steel, Bars, Forgings, and Tubing, 080 Cr, 1.8 Ni, 0.25 Mo (0.38 - 0.43 C) (SAE 4340) Normalized and Tempered

Aerospace Industries Association Standard

NAS410 Certification and Qualification of Nondestructive Test Personnel Aerospace Industries Association of America, Inc., 1250 Eye Street NW, Washington, DC 20005.

Keywords

angle beam; contact method; immersion ultrasonic; longitudinal wave; nondestructive; straight beam; ultrasonic; ultrasonic examination; ultrasonic technique; ultrasound; wrought metal products; wrought metals;

ICS Code

ICS Number Code 71.040.99 (Other standards related to analytical chemistry)

DOI: 10.1520/E2375

ASTM International is a member of CrossRef.

Email *
Password *
Confirm *
First Name *
Last Name *
Title
Company Name *
Company Size *
Industry *
Address *
Address 2
City *
State *	Zip *
Country *
Phone *
How did you hear about MADCAD.com? *

Company*
Full name*
Email*
Phone

Full name*
Email*
Phone
Your selection

MADCAD.com Free Trial

Report To Us

Contact us for a custom quote

To continue with accurate pricing,
please select your company type below:

We need your input!

Cart Warning

Description of ASTM-E2375 2013

ASTM E2375 - 08(2013)

Standard Practice for Ultrasonic Testing of Wrought Products

ASTM E2375

ASTM E2375

This book also exists in the following packages...

Subscription Information

About ASTM

Username:
Password:

MADCAD.com Free Trial

Report To Us

Contact us for a custom quote

To continue with accurate pricing, please select your company type below:

We need your input!

Cart Warning

Description of ASTM-E2375 2013

ASTM E2375 - 08(2013)

Standard Practice for Ultrasonic Testing of Wrought Products

ASTM E2375

ASTM E2375

This book also exists in the following packages...

Subscription Information

About ASTM

To continue with accurate pricing,
please select your company type below: