|
FORMAT
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-E2129 2024ASTM E2129-24Active Standard: Standard Practice for Data Collection for Sustainability Assessment of Building ProductsASTM E2129Scope 1.1 This practice covers a set of instructions for collecting data to be used in assessing the sustainability of building products for use in both commercial and residential buildings. 1.1.1 There are many features of a building that contribute to sustainability; one of them is the selection of products for use in a building. Other key features influencing sustainability include, but are not limited to: overall efficiency of the design of the building, the impact the building has on the habits of the occupants, and the impact the building has on the microclimate and macroclimate. This practice addresses sustainability issues related to building products. This practice does not address sustainability issues related to overall building design, site selection, building operations, or other features influencing sustainability. 1.1.2 While it is recommended that users rely on professional judgment informed by both environmental expertise and specific knowledge of the intended use of the product, this practice provides no instruction as to interpretation of the data obtained. Interpretation of the data obtained is the responsibility of the user of this practice. 1.1.3 This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This practice is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word “standard” in the title means only that the document has been approved through the ASTM consensus process. 1.2 This practice is organized according to the Construction Specifications Institute’s (CSI) MasterFormat2 sections to promote consistency in the evaluation of building products. 1.2.1 CSI MasterFormat version 1995 is used to organize information in Table 2. Appendix X1 provides a cross reference comparison to CSI MasterFormat 2004. 1.3 This practice includes general, comprehensive data requirements. Depending upon the building product, certain data requirements may not apply given the unique characteristics of the product and the potential environmental impacts related to the intended use of the product. Depending upon the building product, certain data requirements may need to be added as appropriate to the unique characteristics of the product and the potential environmental impacts related to the intended use of the product. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords building product; energy efficiency; environmental; green building; indoor environmental quality (IEQ); sustainability; sustainable; sustainable development; ICS Code ICS Number Code 91.010.99 (Other aspects) DOI: 10.1520/E2129-24 The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|