FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-E1418 2010ASTM E1418 - 10Standard Practice for Visible Penetrant Testing Using the Water-Washable ProcessActive Standard ASTM E1418 | Developed by Subcommittee: E07.03 Book of Standards Volume: 03.03 ASTM E1418Significance and Use Liquid penetrant examination methods indicate the presence, location, and, to a limited extent, the nature and magnitude of the detected discontinuities. This practice is normally used for production examination of large volumes of parts or structures, where emphasis is on productivity. This practice offers a wide latitude in applicability when extensive and controlled conditions are available. 1. Scope 1.1 This practice describes procedures for visible liquid penetrant examination utilizing the water-washable process. It is a nondestructive practice for detecting discontinuities that are open to the surface such as cracks, seams, laps, cold shuts, laminations, isolated porosity, through leaks or lack of fusion and is applicable to in-process, final, and maintenance examination. This practice can be effectively used in the examination of nonporous, metallic materials, both ferrous and nonferrous, and of nonmetallic materials such as glazed or fully densified ceramics, and certain nonporous plastics, and glass. 1.2 This practice also provides the following references: 1.2.1 A reference by which visible penetrant examination procedures using the water-washable process can be reviewed to ascertain their applicability and completeness. 1.2.2 For use in the preparation of process specifications dealing with the visible, water-washable liquid penetrant examination of materials and parts. Agreement between the user and the supplier regarding specific techniques is strongly recommended. 1.2.3 For use in the organization of the facilities and personnel concerned with the liquid penetrant examination. 1.3 This practice does not indicate or suggest criteria for evaluation of the indications obtained. It should be noted, however, that after indications have been produced, they must be interpreted or classified and then evaluated. For this purpose there must be a separate code, specification, or a specific agreement to define the type, size, location, and orientation of indications considered acceptable, and those considered unacceptable. 1.4 The values stated in inch-pound units are regarded as standard. SI units given in parentheses are for information only. 1.5 Basis of Application There are areas in this practice that may require agreement between the cognizant engineering organization and the supplier, or specific direction from the cognizant engineering organization. These areas are identified as follows: 1.5.1 Penetrant type, method and sensitivity, 1.5.2 Accept/reject criteria, 1.5.3 Personnel qualification requirements, 1.5.4 Grit blasting, 1.5.5 Etching, 1.5.6 Indication/discontinuity sizing, 1.5.7 Total processing time, and 1.5.8 Marking of parts. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards D129 Test Method for Sulfur in Petroleum Products (General High Pressure Decomposition Device Method) D516 Test Method for Sulfate Ion in Water D808 Test Method for Chlorine in New and Used Petroleum Products (High Pressure Decomposition Device Method) D1552 Test Method for Sulfur in Petroleum Products (High-Temperature Method) E165 Practice for Liquid Penetrant Examination for General Industry E433 Reference Photographs for Liquid Penetrant Inspection E543 Specification for Agencies Performing Nondestructive Testing E1316 Terminology for Nondestructive Examinations ASNT Standards ANSI/ASNT-CP-189 Standard for Qualification and Certification of NDT PersonnelMilitary Standard MIL-STD-410 Nondestructive Testing Personnel Qualification and Certification Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098AIA Standard NAS-410 Certification and Qualification of Nondestructive Test Personnel Available from the Aerospace Industries Association of America, Inc., 1250 Eye Street, N.W., Washington, DC 20005.Keywords nondestructive testing; visible liquid penetrant testing; water-washable method; Discontinuities; Engineering applications; Liquid penetration; Metals and metallic materials; Nondestructive evaluation (NDE); Nonmetallic materials; Nonporous materials; Penetrant inspection; Surface analysis--metals/alloys; Visible liquid penetrant testing; Water washable penetrants ; ICS Code ICS Number Code 19.040 (Environmental testing) DOI: 10.1520/E1418-10 ASTM International is a member of CrossRef. ASTM E1418The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|