|
FORMAT
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D8444/D8444M 2024ASTM D8444/D8444M-24Active Standard: Standard Specification for Fiber Reinforced Polymer Dowel Bars for Load Transfer Between Concrete SlabsASTM D8444/D8444MScope 1.1 This specification covers glass fiber reinforced polymer (GFRP) dowel bars, provided in cut lengths and having a smooth surface so that when embedded in concrete, the expansion and contraction of concrete along the longitudinal axis of the dowel is not inhibited. A dowel bar, commonly referred to as a dowel, acts as a shear transfer device between concrete slabs. In addition, GFRP dowel bars are electromagnetically transparent, lightweight compared to steel, and non-corroding. Dowels covered by this specification shall meet the requirements for geometric, material, mechanical, and physical properties described herein. 1.2 Dowel bars produced according to this standard must meet the requirements using the test methods referenced in Table 1. Quality control and acceptance of production lots of dowel bars must meet the requirements using the test methods referenced in Table 2. 1.3 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables) shall not be considered as requirements of the specification. 1.4 The following dowel bars are not covered by this specification: 1.4.1 Dowel bars made of more than one load-bearing fiber reinforcement type (that is, hybrid FRP). 1.4.2 Dowel bars having an external surface treatment, coating or bond-breaking agent added after production. 1.4.3 Dowel bars having an external surface enhancement for bonding with concrete (that is, bars intended for concrete reinforcement). 1.4.4 Dowel bars with geometries other than solid, round cross sections. 1.5 This specification is applicable for either SI (as Specification D8444M) or inch-pound units (as Specification D8444). 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.6.1 Within the text, the inch-pound units are shown in brackets. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords corrosion resistant dowel bar; dowel bars for concrete street and highway pavement; GFRP dowel bar; GFRP load transfer; non-metallic dowel bar; ICS Code ICS Number Code 91.100.40 (Products in fibre-reinforced cement) DOI: 10.1520/D8444_D8444M-24 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|