FORMAT
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-D5597 1994ASTM D5597-94Withdrawn Standard: Practice for the Preparation of Oil-Based Ink Resin Solutions Using a Hot Oil Bath (Withdrawn 1999)ASTM D5597Scope 1.1 This practice covers a laboratory procedure for preparing an oil-based ink resin solution in a high boiling solvent using a hot oil bath. 1.2 This practice uses laboratory equipment generally available in a normal, well equipped laboratory. 1.3 This practice allows rapid resin solution preparation (typically 30 to 45 min) and regulates the maximum temperature under an inert atmosphere, preventing the random solvent loss during preparation. 1.4 The procedure is for use with ink resins intended mainly for oil-based offset and letterpress inks. The types of resins are typically, but not limited to, C 9 aromatic hydrocarbon resins, modified dicyclopentadiene resins, rosin pentaerythritol or glycerin esters, phenolic-modified rosin esters, maleic anhydride-modified rosin esters, and naturally occurring resins such as gilsonite. 1.5 The typical high boiling solvents to be used include C 12 -C 16 petroleum distillates, texanol isobutyrate, alkali-refined linseed oil, tridecyl alcohol, or combinations of the above. 1.6 To avoid fire or injury to the operator, or both, this procedure should not be used with low flash point solvents such as toluene or xylene. The minimum flash point of the solvents used should be 60°C (140°F) as determined by Test Method D56. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Keywords Compatibility; Dissolution; Hot oil bath; Ink resin solution; Oil-based ink resin solution; Rapid resin solution preparation; Resins; Specimen preparation (for testing)-paints/related coatings; oil-based ink resin solutions-preparation, using hot oil bath,; practice ICS Code ICS Number Code 87.080 (Inks. Printing inks) DOI: This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|