Filters:
FORMAT
EDITION
to
PUBLISHER
AABC
(1)
AAMI
(337)
ACI
(585)
AISC
(54)
ASA
(234)
ASCE
(996)
ASHRAE
(657)
ASME
(2154)
ASSE
(117)
ASTM
(94394)
AWC
(54)
AWWA
(560)
BHMA
(124)
BICSI
(33)
BIFMA
(21)
BOMA
(20)
BSI
(94146)
CHD
(3)
CRSI
(17)
IAHSS
(1)
IAPMO
(374)
ICC
(309)
IEEE
(6631)
IES
(241)
ISEA
(16)
Joint Commission
(177)
Joint Commission Int.
(1)
NETA
(6)
NFPA
(1646)
TCNA
(17)
TMS
(19)
USGBC
(28)
WILEY
(4)
 
AR
(6)
AZ
(7)
CA
(115)
CT
(3)
FL
(57)
ID
(5)
IL
(5)
IN
(1)
KY
(1)
LA
(2)
MI
(25)
MN
(27)
NC
(27)
NJ
(13)
NY
(61)
OH
(24)
OR
(22)
PA
(7)
RI
(8)
SC
(20)
SD
(1)
TX
(3)
VA
(50)
VT
(6)
WA
(31)
CONTENT TYPE
 Act
 Admin Code
 Announcements
 Bill
 Book
 CADD File
 CAN
 CEU
 Charter
 Checklist
 City Code
 Code
 Commentary
 Comprehensive Plan
 Conference Paper
 County Code
 Course
 DHS Documents
 Document
 Errata
 Executive Regulation
 Federal Guideline
 Firm Content
 Guideline
 Handbook
 Interpretation
 Journal
 Land Use and Development
 Law
 Legislative Rule
 Local Amendment
 Local Code
 Local Document
 Local Regulation
 Local Standards
 Manual
 Model Code
 Model Standard
 Notice
 Ordinance
 Other
 Paperback
 PASS
 Periodicals
 PIN
 Plan
 Policy
 Product
 Product - Data Sheet
 Program
 Provisions
 Requirements
 Revisions
 Rules & Regulations
 Standards
 State Amendment
 State Code
 State Manual
 State Plan
 State Standards
 Statute
 Study Guide
 Supplement
 Sustainability
 Technical Bulletin
 All
  • ASTM
    D5206-13 Standard Test Method for Windload Resistance of Rigid Plastic Siding
    Edition: 2013
    $91.10
    Unlimited Users per year

Description of ASTM-D5206 2013

ASTM D5206 - 13

Standard Test Method for Windload Resistance of Rigid Plastic Siding

Active Standard ASTM D5206 | Developed by Subcommittee: D20.24

Book of Standards Volume: 08.03




ASTM D5206

Significance and Use

5.1 This test method is a standard procedure for determining windload resistance of rigid plastic siding under specified uniform static pressure difference. This typically is intended to represent the effects of wind loads on exterior building surfaces. The actual loading on building surfaces is quite complex, varying with wind direction, time, height above ground, building shape, terrain, surrounding structures, and other factors.

5.2 Design wind pressure is selected for specific geographical locations from wind velocity maps prepared by the National Weather Service or other sources. Refer to Annex A1 of Specification D3679 for additional detailed information relating to use of this test method for evaluation of rigid poly(vinyl chloride) (PVC) siding.

Note 2 In applying the results of this test method, note that the performance of rigid PVC siding is a function of installation, and the specimen may or may not truly represent the actual application. In service, performance will also depend on the rigidity of supporting construction, and on the resistance of other components to deterioration by various causes, to thermal expansion and contraction, etc.

1. Scope

1.1 This test method describes methods for testing and evaluating windload resistance of rigid plastic siding when fastened in accordance with Practice D4756 .

1.2 The proper use of this test method requires a knowledge of the principles of pressure measurement.

1.3 This test method describes the apparatus and the procedures to be used to determine an average maximum sustained static test pressure, or ultimate test pressure values, or both, with static pressure applied uniformly to a specimen.

Note 1 There is no known ISO equivalent to this test method.

1.4 The values expressed in inch-pound units are to be regarded as the standard. The SI equivalents in parentheses are for information only.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 7 .


2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

D883 Terminology Relating to Plastics

D1600 Terminology for Abbreviated Terms Relating to Plastics

D3679 Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding

D4756 Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit

E631 Terminology of Building Constructions


Keywords

PVC siding; plastic siding; siding failure modes; test methods; windload resistance ;


ICS Code

ICS Number Code 91.060.10 (Walls. Partitions. Facades)


DOI: 10.1520/D5206-13

ASTM International is a member of CrossRef.

ASTM D5206

The following editions for this book are also available...

This book also exists in the following packages...

Year Publisher Title Annual Price
VAR
ASTM
 [+] $1,278.52 Buy
VAR
ASTM
 [+] $3,362.03 Buy
VAR
ASTM
 [+] $3,560.85 Buy

Subscription Information

MADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.

 

Some features of MADCAD.com ASTM Standards Subscriptions are:

- Online access: With MADCAD.com’ s web based subscription service no downloads or installations are required. Access ASTM Standards from any browser on your computer, tablet or smart phone.

- Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.

 

For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.

 

About ASTM

ASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide.
GROUPS