Filters:
EDITION
to
PUBLISHER
AABC
(1)
AAMI
(343)
ACI
(623)
AECDAILY
(599)
AISC
(55)
ASA
(234)
ASCE
(1019)
ASHRAE
(696)
ASME
(2187)
ASSE
(117)
ASTM
(95582)
AWC
(63)
AWWA
(590)
BHMA
(124)
BICSI
(33)
BIFMA
(24)
BOMA
(20)
BSI
(96542)
CRSI
(17)
IAHSS
(1)
IAPMO
(374)
ICC
(325)
IEEE
(7076)
IES
(241)
ISEA
(21)
Joint Commission
(184)
Joint Commission Int.
(1)
NETA
(7)
NFPA
(1669)
TCNA
(18)
TMS
(19)
USGBC
(28)
WILEY
(4)
 
AR
(6)
AZ
(7)
CA
(115)
CT
(3)
FL
(57)
ID
(5)
IL
(5)
IN
(1)
KY
(1)
LA
(2)
MI
(28)
MN
(27)
NC
(27)
NJ
(13)
NY
(61)
OH
(24)
OR
(22)
PA
(7)
RI
(8)
SC
(20)
SD
(1)
TX
(3)
VA
(50)
VT
(6)
WA
(33)
CONTENT TYPE
 Act
 Admin Code
 Announcements
 Bill
 Book
 CADD File
 CAN
 CEU
 Charter
 Checklist
 City Code
 Code
 Commentary
 Comprehensive Plan
 Conference Paper
 County Code
 Course
 DHS Documents
 Document
 Errata
 Executive Regulation
 Federal Guideline
 Firm Content
 Guideline
 Handbook
 Interpretation
 Journal
 Land Use and Development
 Law
 Legislative Rule
 Local Amendment
 Local Code
 Local Document
 Local Regulation
 Local Standards
 Manual
 Model Code
 Model Standard
 Notice
 Ordinance
 Other
 Paperback
 PASS
 Periodicals
 PIN
 Plan
 Policy
 Product
 Product - Data Sheet
 Program
 Provisions
 Requirements
 Revisions
 Rules & Regulations
 Standards
 State Amendment
 State Code
 State Manual
 State Plan
 State Standards
 Statute
 Study Guide
 Supplement
 Sustainability
 Technical Bulletin
 All
  • ASTM
    D5031/D5031M-13 Standard Practice for Enclosed Carbon-Arc Exposure Tests of Paint and Related Coatings (Redline)
    Edition:
    $144.00
    Unlimited Users per year

Description of ASTM-D5031/D5031M

1.1 This practice covers the selection of test conditions for accelerated exposure testing of coatings and related products in enclosed carbon arc devices operated according to Practices G151 and G153. This practice also covers the preparation of test specimens, the test conditions suited for coatings, and the evaluation of test results. Table 1 describes commonly used test conditions.

1.2 This practice does not cover filtered open-flame carbon-arc exposures of paints and related coatings, which is described in Practice D822/D822M. Another procedure for exposing these products is covered by Practice D3361/D3361M, in which the specimens are subjected to radiation from an unfiltered open-flame carbon arc that produces shorter wavelengths and higher levels of short wavelength radiation than filtered open flame or enclosed carbon arcs.

Note 1—Practice D3361/D3361M requires use of open-flame carbon-arc apparatus with automatic humidity control.

1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
GROUPS