Cart (0)
  • No items in cart.
Total
$0
There is a technical issue about last added item. You can click "Report to us" button to let us know and we resolve the issue and return back to you or you can continue without last item via click to continue button.
Home
Content
eLibrary
Filters:
FORMAT
EDITION
to
PUBLISHER
AABC
(1)
AAMI
(337)
ACI
(589)
AISC
(55)
ASA
(234)
ASCE
(996)
ASHRAE
(690)
ASME
(2161)
ASSE
(117)
ASTM
(94624)
AWC
(54)
AWWA
(575)
BHMA
(124)
BICSI
(33)
BIFMA
(21)
BOMA
(20)
BSI
(94991)
CHD
(3)
CRSI
(17)
IAHSS
(1)
IAPMO
(374)
ICC
(315)
IEEE
(6731)
IES
(241)
ISEA
(16)
Joint Commission
(184)
Joint Commission Int.
(1)
NETA
(6)
NFPA
(1646)
TCNA
(17)
TMS
(19)
USGBC
(28)
WILEY
(4)
 
AR
(6)
AZ
(7)
CA
(115)
CT
(3)
FL
(57)
ID
(5)
IL
(5)
IN
(1)
KY
(1)
LA
(2)
MI
(25)
MN
(27)
NC
(27)
NJ
(13)
NY
(61)
OH
(24)
OR
(22)
PA
(7)
RI
(8)
SC
(20)
SD
(1)
TX
(3)
VA
(50)
VT
(6)
WA
(33)
CONTENT TYPE
 Act
 Admin Code
 Announcements
 Bill
 Book
 CADD File
 CAN
 CEU
 Charter
 Checklist
 City Code
 Code
 Commentary
 Comprehensive Plan
 Conference Paper
 County Code
 Course
 DHS Documents
 Document
 Errata
 Executive Regulation
 Federal Guideline
 Firm Content
 Guideline
 Handbook
 Interpretation
 Journal
 Land Use and Development
 Law
 Legislative Rule
 Local Amendment
 Local Code
 Local Document
 Local Regulation
 Local Standards
 Manual
 Model Code
 Model Standard
 Notice
 Ordinance
 Other
 Paperback
 PASS
 Periodicals
 PIN
 Plan
 Policy
 Product
 Product - Data Sheet
 Program
 Provisions
 Requirements
 Revisions
 Rules & Regulations
 Standards
 State Amendment
 State Code
 State Manual
 State Plan
 State Standards
 Statute
 Study Guide
 Supplement
 Sustainability
 Technical Bulletin
 All
  • ASTM
    D4242-07(2013) Standard Test Method for Inclined Plate Flow for Thermosetting Coating Powders
    Edition: 2013
    $91.10
    Unlimited Users per year

Description of ASTM-D4242 2013

ASTM D4242 - 07(2013)

Standard Test Method for Inclined Plate Flow for Thermosetting Coating Powders

Active Standard ASTM D4242 | Developed by Subcommittee: D01.51

Book of Standards Volume: 06.02




ASTM D4242

Significance and Use

5.1 This test method is useful for selecting coating powders of similar characteristics of melt flow under minimal shear. It is not recommended as an absolute measurement, but rather as a comparative measurement of samples on the same panel measured at the same time.

1. Scope

1.1 This test method specifies a method for determining the flow characteristics of a fused thermosetting coating powder down a plane inclined at a set angle to the horizontal. The test gives an indication of the degree of melt flow that may occur during the curing of the coating powder. This characteristic contributes to the coherence of the coating, to its surface appearance and to the degree of coverage over sharp edges (see Test Method D2967 ), however, it should not be used as the sole factor for judgment. The test acts as a useful method for checking for batch to batch variation in the behavior of a given coating powder. Correlation between the results from coating powders of differing composition is not to be expected. This method is unlikely to yield meaningful results with coating powders which have gel times of less than one minute at the test temperature (see Test Method D4217 ). Oven drafts, angle of inclination and pellet variations significantly affect results making inter-lab reproducibility somewhat difficult to correlate.

1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.


2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement

D2967 Test Method for Corner Coverage of Powder Coatings

D4217 Test Method for Gel Time of Thermosetting Coating Powder

D5965 Test Methods for Specific Gravity of Coating Powders


Keywords

coating powder; pellet flow; pill flow; plate flow; powder coating; thermosetting;


ICS Code

ICS Number Code 83.080.10 (Thermosetting materials)


DOI: 10.1520/D4242

ASTM International is a member of CrossRef.

ASTM D4242

This book also exists in the following packages...

Year Publisher Title Annual Price
VAR
ASTM
 [+] $1,094.15 Buy
VAR
ASTM
 [+] $3,414.42 Buy

Subscription Information

MADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.

 

Some features of MADCAD.com ASTM Standards Subscriptions are:

- Online access: With MADCAD.com’ s web based subscription service no downloads or installations are required. Access ASTM Standards from any browser on your computer, tablet or smart phone.

- Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.

 

For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.

 

About ASTM

ASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide.
GROUPS