1. Scope

1.1 This practice provides recommendations for the installation of buried thermoplastic pipe used in sewers and other gravity-flow applications. These recommendations are intended to ensure a stable underground environment for thermoplastic pipe under a wide range of service conditions. However, because of the numerous flexible plastic pipe products available and the inherent variability of natural ground conditions, achieving satisfactory performance of any one product may require modification to provisions contained herein to meet specific project requirements.

1.2 The scope of this practice necessarily excludes product performance criteria such as minimum pipe stiffness, maximum service deflection, or long term strength. Thus, it is incumbent upon the product manufacturer, specifier, or project engineer to verify and assure that the pipe specified for an intended application, when installed according to procedures outlined in this practice, will provide a long term, satisfactory performance according to criteria established for that application. A commentary on factors important in achieving a satisfactory installation is included in . Specific paragraphs in the appendix are referenced in the body of this practice for informational purposes.

Note 1

The following ASTM standards may be found useful in connection with this practice: Practice D 420, Test Method D 1556, Method D 2216, Specification D 2235, Test Method D 2412, Specification D 2564, Practice D 2657, Practice D 2855, Test Methods D 2922, Test Method D 3017, Practice F 402, Specification F 477, Specification F 545, and Specification F 913.

Most Plumbing Codes and some Building Codes have provisions for the installation of underground 'building drains and building sewers.' See them for plumbing piping applications.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

D8 Terminology Relating to Materials for Roads and Pavements

D420 Guide to Site Characterization for Engineering Design and Construction Purposes

D653 Terminology Relating to Soil, Rock, and Contained Fluids

D698 Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12 400 ft-lbf/ft3 (600 kN-m/m3))

D1556 Test Method for Density and Unit Weight of Soil in Place by Sand-Cone Method

D2216 Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass

D2235 Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings

D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading

D2487 Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)

D2488 Practice for Description and Identification of Soils (Visual-Manual Procedure)

D2564 Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems

D2657 Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings

D2855 Practice for Making Solvent-Cemented Joints with Poly(Vinyl Chloride) (PVC) Pipe and Fittings

D2922 Test Methods for Density of Soil and Soil-Aggregate in Place by Nuclear Methods (Shallow Depth)

D3017 Test Method for Water Content of Soil and Rock in Place by Nuclear Methods (Shallow Depth)

D3839 Guide for Underground Installation of Fiberglass (Glass-FiberReinforced Thermosetting-Resin) Pipe

D4318 Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils

F402 Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings

F412 Terminology Relating to Plastic Piping Systems

F477 Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe

F545 Specification for PVC and ABS Injected Solvent Cemented Plastic Pipe Joints

F913 Specification for Thermoplastic Elastomeric Seals (Gaskets) for Joining Plastic Pipe

F1668 Guide for Construction Procedures for Buried Plastic Pipe

AASHTO Standard

Keywords

backfill; bedding; compaction; embedment; haunching; migration; sewer pipe; soil stiffness; thermoplastic; underground installation; Backfill; Deflection--plastics; Gravity sewer pipe; Haunching; Sewer pipe (thermoplastic); Thermoplastic pipe/tube/fittings; Underground installation--water supply/distribution systems;

ICS Code

ICS Number Code 23.040.20 (Plastic pipes)

DOI: 10.1520/D2321-04E01

ASTM International is a member of CrossRef.