FORMAT
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-C595 2013ASTM C595 / C595M - 13Standard Specification for Blended Hydraulic CementsActive Standard ASTM C595 / C595M | Developed by Subcommittee: C01.10 Book of Standards Volume: 04.01
Translated Standard: Spanish ASTM C595 / C595MAbstract This specification pertains to blended hydraulic cements for both general and special applications, using slag or pozzolan, or both, with portland cement or portland cement clinker or slag with lime. These cements are classified into two types: Type IS which is portland blast-furnace slag cement and Type IP which is portland-pozzolan cement. They can also be described according to air-entraining, moderate sulfate resistance, moderate heat of hydration, high sulfate resistance, or low heat of hydration properties. The cement shall conform to the chemical requirements prescribed. In addition, the cement shall undergo different tests to determine the following properties: chemical analysis, fineness by sieving, fineness by air-permeability, autoclave expansion, time of setting, air content of mortar, compressive strength, heat of hydration, normal consistency, specific gravity, water requirement, mortar expansions of blended cement and pozzolan, drying shrinkage, activity index with Portland cement, and sulfate resistance. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Significance and Use A2.3. Significance and Use A2.3.1 This annex provides a means to determine the amount of methylene blue dye adsorbed by a sample of finely ground limestone. Methylene blue dye is preferentially adsorbed by clay minerals that may be present in limestone. The amount of dye adsorbed is related to the clay type and content. Certain clays may increase the water demand or affect other properties of cements if present in sufficient quantity in the limestone when used as an ingredient in cement. The specification places a limit on the methylene blue index of limestone permitted as an ingredient in blended cement. 1. Scope 1.1 This specification pertains to blended hydraulic cements for both general and special applications, using slag, pozzolan, limestone, or some combination of these, with portland cement or portland cement clinker or slag with lime.
Note 1 This specification prescribes ingredients and proportions, with some performance requirements whereas
Performance Specification C1157 is a hydraulic cement specification in which performance criteria alone govern the products and their acceptance.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Values in SI units [or inch-pound units] shall be obtained by measurement in SI units [or inch-pound units] or by appropriate conversion, using the Rules for Conversion and Rounding given in IEEE/ASTM SI 10 , of measurements made in other units [or SI units]. Values are stated in only SI units when inch-pound units are not used in practice. 1.3 The text of this standard refers to notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) are not requirements of the standard.
CSA Standards CSAA3004-D2 Determination of Total Organic Carbon in LimestoneASTM Standards C51 Terminology Relating to Lime and Limestone (as used by the Industry) C109/C109M Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens) C114 Test Methods for Chemical Analysis of Hydraulic Cement C150 Specification for Portland Cement C151 Test Method for Autoclave Expansion of Hydraulic Cement C157/C157M Test Method for Length Change of Hardened Hydraulic-Cement Mortar and Concrete C183 Practice for Sampling and the Amount of Testing of Hydraulic Cement C185 Test Method for Air Content of Hydraulic Cement Mortar C186 Test Method for Heat of Hydration of Hydraulic Cement C187 Test Method for Amount of Water Required for Normal Consistency of Hydraulic Cement Paste C188 Test Method for Density of Hydraulic Cement C191 Test Methods for Time of Setting of Hydraulic Cement by Vicat Needle C204 Test Methods for Fineness of Hydraulic Cement by Air-Permeability Apparatus C219 Terminology Relating to Hydraulic Cement C226 Specification for Air-Entraining Additions for Use in the Manufacture of Air-Entraining Hydraulic Cement C227 Test Method for Potential Alkali Reactivity of Cement-Aggregate Combinations (Mortar-Bar Method) C311 Test Methods for Sampling and Testing Fly Ash or Natural Pozzolans for Use in Portland-Cement Concrete C430 Test Method for Fineness of Hydraulic Cement by the 45-m (No. 325) Sieve C465 Specification for Processing Additions for Use in the Manufacture of Hydraulic Cements C511 Specification for Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks Used in the Testing of Hydraulic Cements and Concretes C563 Test Method for Approximation of Optimum SO3 in Hydraulic Cement Using Compressive Strength C688 Specification for Functional Additions for Use in Hydraulic Cements C821 Specification for Lime for Use with Pozzolans C1012 Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution C1038 Test Method for Expansion of Hydraulic Cement Mortar Bars Stored in Water C1157 Performance Specification for Hydraulic Cement E11 Specification for Woven Wire Test Sieve Cloth and Test Sieves E350 Test Methods for Chemical Analysis of Carbon Steel, Low-Alloy Steel, Silicon Electrical Steel, Ingot Iron, and Wrought Iron E1019 Test Methods for Determination of Carbon, Sulfur, Nitrogen, and Oxygen in Steel, Iron, Nickel, and Cobalt Alloys by Various Combustion and Fusion Techniques Keywords blended hydraulic cement; fly ash cement; hydraulic cement; portland blast-furnace slag cement; portland-limestone cement; portland pozzolan cement; pozzolanic cement; slag; granulated blast furnace slag; ICS Code ICS Number Code 91.100.10 (Cement. Gypsum. Lime. Mortar) DOI: 10.1520/C0595_C0595M-13 ASTM International is a member of CrossRef. ASTM C595 / C595MThe following editions for this book are also available...
This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|