Abstract

This specification covers four types of hydrated lime. Type N and S are suitable for use in mortar, in scratch and brown coats of cement plaster, for stucco, and for addition to Portland-cement concrete. Types NA and SA are air-entrained hydrated limes that are suitable for use in any of the above uses where the inherent properties of lime and air-entrainment are desired. The four types of lime under this specification shall be designated as Type N which is the normal hydrated lime for masonry purposes, type S which is the special hydrated lime for masonry purposes, type NA which is the normal air-entraining hydrated lime for masonry purposes and type SA which is the special air-entraining hydrated lime for masonry purposes. Hydrated lime for masonry purposes shall conform to the required chemical composition for calcium and magnesium oxides and carbon dioxide. The hydrated lime covered by Types N or S in this specification shall contain no additives for the purpose of entraining air.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification covers four types of hydrated lime. Types N and S are suitable for use in mortar, in scratch and brown coats of cement plaster, for stucco, and for addition to portland-cement concrete. Types NA and SA are air-entrained hydrated limes that are suitable for use in any of the above uses where the inherent properties of lime and air-entrainment are desired. The four types of lime sold under this specification shall be designated as follows:

1.1.1 Type N Normal hydrated lime for masonry purposes.

1.1.2 Type S Special hydrated lime for masonry purposes.

1.1.3 Type NA Normal air-entraining hydrated lime for masonry purposes.

1.1.4 Type SA Special air-entraining hydrated lime for masonry purposes.

Note 1Type S, special hydrated lime, and Type SA, special air-entraining hydrated lime, are differentiated from Type N, normal hydrated lime, and Type NA, normal air-entraining hydrated lime, principally by their ability to develop high, early plasticity and higher water retentivity, and by a limitation on their unhydrated oxide content.

Note 2For normal (Type N) and special (Type S) finishing hydrated lime, refer to Specification C206 .

Note 3Some building codes prohibit the use of air-entraining materials in mortar, because of the accompanying reduction in bond and compressive strength. Where increased freeze-thaw resistance is important, air-entraining may be beneficial. Air-entraining lime should not be used as a finishing lime.

Note 4For lime putty, refer to Specification C1489 .

1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

C25 Test Methods for Chemical Analysis of Limestone, Quicklime, and Hydrated Lime

C50 Practice for Sampling, Sample Preparation, Packaging, and Marking of Lime and Limestone Products

C110 Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone

C206 Specification for Finishing Hydrated Lime

C226 Specification for Air-Entraining Additions for Use in the Manufacture of Air-Entraining Hydraulic Cement

C778 Specification for Sand

C1489 Specification for Lime Putty for Structural Purposes

Keywords

hydrated lime; masonry; mortar; plasticity; popping and pitting; residue; stucco; Type N; Type NA; Type S; Type SA; unhydrated oxides; water retention; air entraining; Cement materials/applications--specifications; Hydrated lime--specifications; Masonry mortar and grout--specifications;

ICS Code

ICS Number Code 91.100.10 (Cement. Gypsum. Lime. Mortar)

DOI: 10.1520/C0207-06R11

ASTM International is a member of CrossRef.

ASTM C207