ASTM B103/B103M-09
Historical Standard: ASTM B103/B103M-09 Standard Specification for Phosphor Bronze Plate, Sheet, Strip, and Rolled Bar
SUPERSEDED (see Active link, below)
ASTM B103 / B103M
1. Scope
1.1 This specification establishes copper-tin alloy (phosphor bronze), copper-tin-lead alloy (leaded phosphor bronze), and copper-tin-lead-zinc alloy (bearing bronze), plate, sheet, strip, and rolled bar. The phosphor bronzes commonly are used for deep drawing into bellows and stamping and forming into spring devices and into terminals and connectors for electrical apparatus because they combine high strength with high elongation. The leaded phosphor bronzes are used where strength, corrosion resistance, and machinability are required. The bearing bronze is used in bushings, bearings, and load-bearing thrust washers. The following alloys are covered:
| Copper Alloy UNS No. | Nominal Composition, % | Previously Used Designation | |||
| Copper | Tin | Zinc | Lead | ||
| C51000 | 95 | 5 | . . . | . . . | A1 |
| C51100 | 96 | 4 | . . . | . . . | A |
| C51180 | 96 | 4 | . . . | . . . | . . . |
| C51900 | 94 | 6 | . . . | . . . | |
| C52100 A | 92 | 8 | . . . | . . . | C |
| C52180 | 92 | 8 | . . . | . . . | . . . |
| C52400 | 90 | 10 | . . . | . . . | D |
| C53400 | 94 | 5 | . . . | 1 | B1 |
| C54400 | 88 | 4 | 4 | 4 | B2 |
| __________________ | |||||
A SAE Specification CA 521 conforms to the requirements of UNS No. C52100.
Note 1All of the above alloys contain small amounts of phosphorus, used as a deoxidant in melting, and to enhance the mechanical properties.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
B248 Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar
B248M Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar (Metric)
B601 Classification for Temper Designations for Copper and Copper Alloys--Wrought and Cast
B846 Terminology for Copper and Copper Alloys
E8 Test Methods for Tension Testing of Metallic Materials
E8M Test Methods for Tension Testing of Metallic Materials [Metric]
E54 Test Methods for Chemical Analysis of Special Brasses and Bronzes
E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E75 Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys
E255 Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition
E478 Test Methods for Chemical Analysis of Copper Alloys
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
Keywords
copper-tin alloy plate; copper-tin alloy rolled bar; copper-tin alloy sheet; copper-tin alloy strip; copper-tin-lead alloy plate; copper-tin-lead alloy rolled bar; copper-tin-lead alloy sheet; copper-tin-lead alloy strip; copper-tin-lead-zinc alloy plate; copper-tin-lead-zinc alloy rolled bar; copper-tin-lead-zinc alloy sheet; copper-tin-lead-zinc alloy strip; copper-tin-lead-zinc-iron alloy sheet; copper-tin-lead-zinc-iron alloy strip; Bronze plate/sheet/strip/rolled bar; Copper alloy plate/sheet/strip/rolled bar--specifications; Phosphor bronze; UNS C51000 (phosphor bronze, 5% A); UNS C51100 (phosphor bronze); UNS C51900 (phosphor bronze); UNS C52100 (phosphor bronze, 8% C); UNS C52400 (phosphor bronze, 10% D); UNS C53400 (phosphor bronze B-1); UNS C54400 (phosphor bronze B-2) ^STATUS: Dn Cn Sn Nn Mn;
ICS Code
ICS Number Code 77.150.30 (Copper products)
DOI: 10.1520/B0103_B0103M-09
ASTM International is a member of CrossRef.
