1. Scope

1.1 This specification covers a group of common requirements that shall apply to wrought steel piping fittings covered in any of the following individual product specifications or any other ASTM specification that invokes this specification or portions thereof:

1.2 In case of conflict between a requirement of the individual product specification and a requirement of this general requirement specification, the requirements of the individual product specification shall prevail over those of this specification.

1.3 By mutual agreement between the purchaser and the supplier, additional requirements may be specified (See 4.1.7). The acceptance of any such additional requirements shall be dependent on negotiations with the supplier and must be included in the order as agreed upon by the purchaser and supplier.

1.4 The values stated in either inch-pound units or SI units [metric] are to be regarded separately as standard. Within the text and the tables, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the M designation [SI] of the product specification is specified in the order.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

A29/A29M Specification for Steel Bars, Carbon and Alloy, Hot-Wrought, General Requirements for

A234/A234M Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service

A262 Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels

A370 Test Methods and Definitions for Mechanical Testing of Steel Products

A388/A388M Practice for Ultrasonic Examination of Steel Forgings

A403/A403M Specification for Wrought Austenitic Stainless Steel Piping Fittings

A420/A420M Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service

A700 Practices for Packaging, Marking, and Loading Methods for Steel Products for Shipment

A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

A758/A758M Specification for Wrought-Carbon Steel Butt-Welding Piping Fittings with Improved Notch Toughness

A763 Practices for Detecting Susceptibility to Intergranular Attack in Ferritic Stainless Steels

A774/A774M Specification for As-Welded Wrought Austenitic Stainless Steel Fittings for General Corrosive Service at Low and Moderate Temperatures

A815/A815M Specification for Wrought Ferritic, Ferritic/Austenitic, and Martensitic Stainless Steel Piping Fittings

A858/A858M Specification for Heat-Treated Carbon Steel Fittings for Low-Temperature and Corrosive Service

A860/A860M Specification for Wrought High-Strength Ferritic Steel Butt-Welding Fittings

A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys

A967 Specification for Chemical Passivation Treatments for Stainless Steel Parts

A1058 Test Methods for Mechanical Testing of Steel Products--Metric

E165 Practice for Liquid Penetrant Examination for General Industry

E213 Practice for Ultrasonic Testing of Metal Pipe and Tubing

E709 Guide for Magnetic Particle Testing

E1916 Guide for Identification of Mixed Lots of Metals

Manufacturers Standardization Society Standards

ASME Standards

Keywords

austenitic stainless steel; corrosive service applications; ferritic/austenitic stainless steel; ferritic stainless steel; high strength low alloy steel; martensitic stainless steel; piping applications; pressure containing parts; pressure vessel service; stainless steel fittings; temperature service applications-elevated; temperature service applications-low; temperature service applications-moderate ;

ICS Code

ICS Number Code 77.140.20 (Steels of high quality); 23.040.40 (Metal fittings)

DOI: 10.1520/A0960_A0960M-08

ASTM International is a member of CrossRef.