FORMAT
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-A82 2007ASTM A82 / A82M - 07Standard Specification for Steel Wire, Plain, for Concrete ReinforcementActive Standard ASTM A82 / A82M | Developed by Subcommittee: A01.05 Book of Standards Volume: 01.04 ASTM A82 / A82MAbstract
This specification covers as cold-drawn or galvanized steel wires to be used as such, or in fabricated form, for the reinforcement of concrete. The steel shall be made by one of the following processes: open-hearth, electric furnace, or basic-oxygen. The wires shall be cold drawn from rods that have been hot rolled from billets. The tests described include tension, bending, and reduction of area tests. After undergoing tension test, the tensile and yield strength properties of the test specimen shall conform to the requirements of a reference material based on nominal area of the wire. The specimen for bend test shall withstand being bent at room temperature without cracking on the outside of the bent portion. The reduction of area shall be determined as described in a reference document. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. 1. Scope
1.1 This specification covers cold-drawn steel wire, as-drawn or galvanized, to be used as such, or in fabricated form, for the reinforcement of concrete, in sizes not less than 2.03 mm [0.080 in.] nominal diameter. 1.2 Supplement S1 describes high-strength wire, which shall be furnished when specifically ordered. It shall be permissible to furnish high-strength wire in place of regular wire if mutually agreed to by the purchaser and the manufacturer. 1.3 The values stated in SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard (The inch-pound units are shown in brackets except in Table 6.) ASTM Standards A185/A185M Specification for Steel Welded Wire Reinforcement, Plain, for Concrete A370 Test Methods and Definitions for Mechanical Testing of Steel Products A641/A641M Specification for Zinc-Coated (Galvanized) Carbon Steel Wire A700 Practices for Packaging, Marking, and Loading Methods for Steel Products for Shipment E83 Practice for Verification and Classification of Extensometer Systems U.S. Military Standards MIL-STD-129 Marking for Shipment and StorageU.S. Federal Standard Fed.Std.No.123 Marking for Shipments (Civil Agencies)ACI Standard ACI318 Building Code Requirements for Structural ConcreteKeywords concrete reinforcement; reinforced concrete; reinforcing steels; steel wire; ICS Code ICS Number Code 77.140.15 (Steels for reinforcement of concrete) DOI: 10.1520/A0082_A0082M-07 ASTM International is a member of CrossRef. ASTM A82 / A82MCustomers who bought this book also bought...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|