|
FORMAT
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-A554 2015ASTM A554-15aHistorical Standard: Standard Specification for Welded Stainless Steel Mechanical TubingASTM A554Scope 1.1 This specification covers welded austenitic, ferritic, and austenitic-ferritic duplex stainless steel mechanical tubing intended for use in ornamental, structural, exhaust, and other applications where appearance, mechanical properties, or corrosion resistance is needed. The grades covered are listed in Table 1.
(A) Maximum, unless a range or minimum is indicated. Where ellipses (...) appear in this table, there is no
minimum and analysis for the element need not be determined or reported.
(B) For small diameter or thin walls, or both, where many drawing passes are required, a carbon content of
0.040 % max is necessary in grades MT-304L and MT-316L. Small outside diameter tubes are defined as those less than 0.500 in. (12.7 mm) in outside diameter and light wall tubes as those less
than 0.049 in. (1.24 mm) in average wall thickness.
(C) The columbium content shall be not less than ten times the carbon content and not more than 1.00 %.
(D) The titanium content shall be not less than five times the carbon content and not more than 0.60 %.
(E) S40900 (Type 409) has been replaced by S40910, S40920, and S40930. Unless otherwise specified in the
ordering information, an order specifying S40900 or Type 409, shall be satisfied by any one of S40910, S40920, or S40930 at the option of the seller. Material meeting the requirements of
S40910, S40920, or S40930 may, by agreement between purchaser and manufacturer, be certified as S40900.
(F) S41003 chemical composition relates to Type 412, which is not currently an AISI or SAE number.
(G) S44100 chemical composition relates to Type 441, which is not currently an AISI or SAE number.
(H) % Cr + 3.3 × %Mo + 16 × %N = 41 min.
(I) % Cr + 3.3 × %Mo + 16 × %N = 40 min.
(J) Designation established in accordance with Practice E527 and SAE J
1086.
(K) Common name, not a trademark, widely used, not associated with any one producer.
1.2 This specification covers as-welded or cold-reduced mechanical tubing in sizes to 16 in. (406.4 mm) outside dimension, and in wall thicknesses 0.020 in. (0.51 mm) and over. 1.3 Tubes shall be furnished in one of the following shapes as specified by the purchaser: round, square, rectangular, or special. 1.4 Supplementary requirements of an optional nature are provided and when desired shall be so stated in the order. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Keywords austenitic stainless steel; austenitic-ferritic duplex stainless steel; exhaust tubing; ferritic stainless steel tubing; mechanical tubing; ornamental tubing; stainless steel tube; steel tube; structural tubing; welded steel tube ; ICS Code ICS Number Code 23.040.10 (Iron and steel pipes) DOI: 10.1520/A0554-15A This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|