1. Scope

1.1 This specification covers stainless steel wire and welded wire reinforcement produced from hot-rolled stainless steel rod. The stainless steel wire is cold-worked, drawn or rolled, plain (non-deformed) or deformed or a combination of deformed and plain. It is used as concrete reinforcement for applications requiring resistance to corrosion and/or controlled magnetic permeability. Common wire sizes and dimensions are found in this specification. Actual wire sizes are not restricted to those shown in the tables.

1.2 Supplement S1 describes high strength wire, which shall be furnished when specifically ordered. It shall be permissible to furnish high strength wire in place of regular wire if mutually agreed to by the purchaser and supplier.

1.2.1 A supplementary requirement (S2) of an optional nature is provided. It shall apply only when specified by the purchaser. In order to obtain a corrosion tested or controlled magnetic permeability product, steel conforming to Supplementary Requirement S2 should be ordered.

1.3 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values may result in nonconformance with the specification.

1.4 The chemical composition of the steel (stainless grade) shall be selected for suitability to the application involved by agreement between the manufacturer and the purchaser. Use Specification A 276 for chemical requirements. The UNS designations are to be included with the type number and noted in brackets, i.e. austenitic stainless steels as Type 304 [S30400], 304L [S30403], 316 [S31600], 316L [S31603], 316N [S31651], 316LN [S31653] and duplex stainless steels, Types 2205 [S32205] and 329 [S32900].

Only austenitic and duplex stainless steels are usually recommended for use as reinforcement in concrete because of their high corrosion resistance. Austenitic stainless steels have good general corrosion resistance, strength characteristics which can be improved by cold working, good toughness and ductility properties at low temperatures, and low magnetic permeability. Duplex stainless steels have generally a corrosion resistance greater than that of most austenitic steels and are magnetic. Other stainless steels with different chemical compositions than the series and types mentioned above, may be used for less restrictive applications.

1.5 Wire for welded wire reinforcement is generally manufactured at 520 MPa [75 ksi] yield strength level. Other strength levels shall be by agreement between the purchaser and manufacturer.

The term used to refer to yield strength levels are the same as those in ASTM Standards for welded wire reinforcement.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Federal Standard

ACI Standard

Military Standards

ASTM Standards

A82/A82M Specification for Steel Wire, Plain, for Concrete Reinforcement

A185/A185M Specification for Steel Welded Wire Reinforcement, Plain, for Concrete

A276 Specification for Stainless Steel Bars and Shapes

A342/A342M Test Methods for Permeability of Feebly Magnetic Materials

A370 Test Methods and Definitions for Mechanical Testing of Steel Products

A496/A496M Specification for Steel Wire, Deformed, for Concrete Reinforcement

A497/A497M Specification for Steel Welded Wire Reinforcement, Deformed, for Concrete

A700 Practices for Packaging, Marking, and Loading Methods for Steel Products for Shipment

E83 Practice for Verification and Classification of Extensometer Systems

Keywords

concrete reinforcement; corrosion resistance; deformations; magnetic properties; reinforced concrete; reinforcing steels; stainless steel welded wire reinforcement; stainless wire; steel wire; welded wire reinforcement;

ICS Code

ICS Number Code 77.140.20 (Steels of high quality)

DOI: 10.1520/A1022_A1022M-06

ASTM International is a member of CrossRef.