|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-G203 2010ASTM G203 - 10Standard Guide for Determining Friction Energy Dissipation in Reciprocating TribosystemsActive Standard ASTM G203 | Developed by Subcommittee: G02.50 Book of Standards Volume: 03.02 ASTM G203Significance and Use Many sliding systems exhibit intermittent high friction force excursions compared to competing tribosystems. However, where friction forces or friction coefficients are averaged, the test data may show that the two systems have the same friction characteristics, when in fact they were not the same; there was a friction problem in the one with the periodic aberrations. The FED takes into account all friction forces that occur in the test increment. It is all of the friction energy that the couple dissipated in the designated test duration. It captures the friction profile of a system in a single number that can be used to screen candidate couples for friction characteristics. If the friction energy used in a reciprocating tribosystem is of concern this metric along with the friction recording, average coefficient of friction, and standard deviation of the force readings, produces the most meaningful data. It is a metric of the energy loss in a tribosystem. 1. Scope 1.1 This guide covers and is intended for use in interpreting the friction forces recorded in reciprocating tribosystems. The guide applies to any reciprocating tribosystem, whether it is a wear or fretting test or an actual machine or device. 1.2 The energy dissipation guide was developed in analyzing friction results in the Test Method G133 reciprocating ball-on-flat test, but it applies to other ASTM or ISO reciprocating tests. This technique is frequently used to record the friction response in fretting tribosystems. 1.3 Specimen material may play some role in the results if the materials under test display viscoelastic behavior. This guide as written is for metals, plastics, and ceramics that do not display viscoelastic behavior. It also applies to lubricated and non-lubricated contacts. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards G40 Terminology Relating to Wear and Erosion G115 Guide for Measuring and Reporting Friction Coefficients G133 Test Method for Linearly Reciprocating Ball-on-Flat Sliding Wear G163 Guide for Digital Data Acquisition in Wear and Friction Measurements Keywords friction; friction coefficient; friction energy; ICS Code ICS Number Code 21.260 (Lubrication systems) DOI: 10.1520/G0203-10 ASTM International is a member of CrossRef. ASTM G203The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|