FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-E1053 2011ASTM E1053 - 11Standard Test Method to Assess Virucidal Activity of Chemicals Intended for Disinfection of Inanimate, Nonporous Environmental SurfacesActive Standard ASTM E1053 | Developed by Subcommittee: E35.15 Book of Standards Volume: 11.05 ASTM E1053Significance and Use This test method may be used to determine the effectiveness of liquid, aerosols/foams, and trigger-spray products against designated prototype viruses. The number of lots of the test substance and the number of replicates in each test will depend on the requirements of the target regulatory agency. Certain regulatory agencies may require additional testing using other carrier tests for product registration purposes. 1. Scope 1.1 This test method is used to evaluate the virucidal efficacy of liquid, aerosol, or trigger-spray microbicides intended for use on inanimate, nonporous environmental surfaces. This test method may be employed with most viruses, which can be grown in cultured cells. However, other host systems (for example, embryonic eggs) may be used with proper justification and documentation. 1.2 This test method should be performed only by those trained in microbiological and virological techniques in facilities designed and equipped for work with infectious agents at the appropriate biosafety level. 1.3 It is the responsibility of the investigator to determine whether Good Laboratory Practice regulations (GLPs) are required and to follow them where appropriate (40 CFR, Part 160 for EPA submissions and 21 CFR, Part 58 for FDA submissions). Refer to the appropriate regulatory agency for performance standards of virucidal efficacy. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The user should consult a reference for laboratory safety recommendations.
ASTM Standards D1129 Terminology Relating to Water E1153 Test Method for Efficacy of Sanitizers Recommended for Inanimate Non-Food Contact Surfaces E1482 Test Method for Neutralization of Virucidal Agents in Virucidal Efficacy Evaluations E2197 Quantitative Disk Carrier Test Method for Determining Bactericidal, Virucidal, Fungicidal, Mycobactericidal, and Sporicidal Activities of Chemicals Federal Standards Title40, Code of Federal Regulations (CFR), Environmental Protection Agency, Subchapter E, Pesticide Programs; Part 160, Good Laboratory Practice StandardsKeywords carrier test; cell or other tissue cultures; disinfectant; infection control; microbicide; surface test; virucidal test; virus; viruses on dried environmental surfaces; Cytotoxicity; Disinfectants/disinfection; Efficacy; Embryonated eggs; Inanimate surfaces; Laboratory environmental analysis; Microbiological examination; Surface analysis--environmental applications; Suspension tests; Tissue culture host systems; Virology; ICS Code ICS Number Code 65.100.01 (Pesticides and other agrochemicals) DOI: 10.1520/E1053-11 ASTM International is a member of CrossRef. ASTM E1053The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|