FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-C509 2011ASTM C509 - 06(2011)Standard Specification for Elastomeric Cellular Preformed Gasket and Sealing MaterialActive Standard ASTM C509 | Developed by Subcommittee: C24.73 Book of Standards Volume: 04.07 ASTM C509Abstract This specification covers elastomeric cellular preformed gasket and sealing materials. Elastomeric cellular materials shall be manufactured from natural rubber, synthetic rubber, rubber-like materials, or mixture of these, with added compounding ingredients. The material shall conform to the required physical properties such as: compression-deflection, compression set, heat aging, dimensional stability, ozone resistance, low-temperature brittleness, water absorption, flame propagation, and nonstaining. The two classifications of material according to ozone resistance are Type I and Type II. Test for each physical properties shall be made. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Significance and Use Flame Propagation : This specification has two options: Option I Flame propagation test is required. Option II Flame propagation test is not required. In case no option is specified, Option I will apply. This specification has two classifications as related to ozone resistance. These are Type I and Type II, with the latter having the greater resistance to ozone. The type should be specified when making reference to this specification but in the event that the type is not specified, Type II shall apply. Note 2Type II is included in this specification for use where greater ozone resistance is required. 1. Scope DESIG 1.1 This specification applies to those elastomeric cellular materials of a firm grade that are manufactured in preformed shapes for use as gaskets and for use as sealing materials, in the form of compression seals or gaskets, or both, for glazing other building joint applications. Note 1For softer cellular elastomeric materials used in secondary sealing applications, refer to Specification D1056 . 1.2 Test Method C1166 , as referenced in this specification, should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use . 1.3 The following precautionary caveat pertains only to the test method portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations. X1.1.1 This test method is intended to determine the ability of compounds made from rubber or rubber-like materials to resist the effect of low temperatures that may cause them to become brittle and fracture or crack when bent. Standard specimens are exposed to specified low temperatures for definite periods after which the specimens are bent in a prescribed manner and any fracture or cracking noted. The procedure is commonly called the Thiokol method. Note X1.1Results obtained by this test method are influenced by the rate of flexing of the cooled specimens which can not be closely controlled in the prescribed apparatus. They are therefore of a qualitative nature and may not be closely reproducible over a range of several degrees of temperature depending on the speed of flexure. For more accurate determination of brittle temperature, and particularly in new specifications, Test Method D746 is recommended.
ASTM Standards C717 Terminology of Building Seals and Sealants C1083 Test Method for Water Absorption of Cellular Elastomeric Gaskets and Sealing Materials C1166 Test Method for Flame Propagation of Dense and Cellular Elastomeric Gaskets and Accessories D395 Test Methods for Rubber Property--Compression Set D412 Test Methods for Vulcanized Rubber and Thermoplastic Elastomers--Tension D746 Test Method for Brittleness Temperature of Plastics and Elastomers by Impact D865 Test Method for Rubber--Deterioration by Heating in Air (Test Tube Enclosure) D925 Test Methods for Rubber Property--Staining of Surfaces (Contact, Migration, and Diffusion) D1056 Specification for Flexible Cellular Materials--Sponge or Expanded Rubber D1149 Test Methods for Rubber Deterioration--Cracking in an Ozone Controlled Environment Keywords cellular; compression; elastomer; elastomeric; gasket; glazing; preformed; seal; sealing; Cellular materials; Compression seals--specifications; Elastomeric seals/sealants--specifications; Gaskets--specifications; Glazing compounds/applications--specifications; Preformed sealant tapes--specifications; Sealants--specifications; ICS Code ICS Number Code 83.140.50 (Seals) DOI: 10.1520/C0509-06R11 ASTM International is a member of CrossRef. ASTM C509This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|